Marksmen know the value of keeping their firearms clean and often enjoy a customized finish. They also want products that do no harm to synthetics, ferrous metals, wood, stainless steel and alloys. Most people prefer no need for heating and baking their firearms which make DuraCoat Aerosol a perfect choice. Here are some points to consider when contacting a Lawrence, KS supplier who also offers Peel 'N Spray templates.
Some people like a smooth finish and others like some other type of texture. Just about any surface is possible with these products ranging from camo to a pearl texture. It is even possible to create layers of texture and then finish them off with a protective coating of the clear product to reduce dings and scratches.
One thing to remember is mixing this product with a hardener. It helps speed up drying time without reducing quality or appearance. Ratios of 12:1 is standard but for faster drying times slightly increase the amount of hardener. It also gives a higher gloss finish at about a 10:1 ratio. Read the directions on the product to make sure of the mixture.
When using the stick on templates, they leave an adhesive residue that is easily removed using mineral spirits and a clean, dry cloth. Be sure to remove all of the adhesive before applying a coat of the DuraClear so that they do not leave bubbles on the finished project. Also use a good cleaner to remove oil, grease, and any other contaminants before applying new finishes.
Typical drying time is overnight. Placing the weapon in an oven for just 1 hour and baking it for about an hour at 110 degrees F speeds up the drying process. At this point, it is possible to use abrasive solvents, lubricants, and cleaners without destroying the finish. For full curing time allow three to six weeks.
Many people like the idea of colorizing their weapons and are amazed to find out that there are over 200 factory colors available. Then they find out all of these colors are mixable to create any color and shade necessary to make their weapons unique from those of anyone else.
Remember that a clean surface is the best to ensure the desired results of any firearm customization. Once dismantled check all interior surfaces, and if necessary use a mirror to make sure all corners and crevices are clear of debris. DuraCoat Cleaner is excellent for this procedure because it leaves no film or residue.
Always dismantle a gun for safety reasons before attempting to clean it, repair it, or refinish it. Make sure all compartments have no ammunitions in them. Check the cylinder, the bullet clip and chamber to make sure the gun is unloaded. Then dismantle it and mask off any areas not intended for DuraCoat before spraying the product on the pieces.
Keep gun safety at the forefront of all activity involving a pistol, rifle or automatic weapon. After all, you could accidentally shoot yourself! The ask a well-trusted supplier about this new technology that allows people to customize their guns. Choose the colors and textures you like best and enjoy a new experience with a gun that reflects your personality.
Some people like a smooth finish and others like some other type of texture. Just about any surface is possible with these products ranging from camo to a pearl texture. It is even possible to create layers of texture and then finish them off with a protective coating of the clear product to reduce dings and scratches.
One thing to remember is mixing this product with a hardener. It helps speed up drying time without reducing quality or appearance. Ratios of 12:1 is standard but for faster drying times slightly increase the amount of hardener. It also gives a higher gloss finish at about a 10:1 ratio. Read the directions on the product to make sure of the mixture.
When using the stick on templates, they leave an adhesive residue that is easily removed using mineral spirits and a clean, dry cloth. Be sure to remove all of the adhesive before applying a coat of the DuraClear so that they do not leave bubbles on the finished project. Also use a good cleaner to remove oil, grease, and any other contaminants before applying new finishes.
Typical drying time is overnight. Placing the weapon in an oven for just 1 hour and baking it for about an hour at 110 degrees F speeds up the drying process. At this point, it is possible to use abrasive solvents, lubricants, and cleaners without destroying the finish. For full curing time allow three to six weeks.
Many people like the idea of colorizing their weapons and are amazed to find out that there are over 200 factory colors available. Then they find out all of these colors are mixable to create any color and shade necessary to make their weapons unique from those of anyone else.
Remember that a clean surface is the best to ensure the desired results of any firearm customization. Once dismantled check all interior surfaces, and if necessary use a mirror to make sure all corners and crevices are clear of debris. DuraCoat Cleaner is excellent for this procedure because it leaves no film or residue.
Always dismantle a gun for safety reasons before attempting to clean it, repair it, or refinish it. Make sure all compartments have no ammunitions in them. Check the cylinder, the bullet clip and chamber to make sure the gun is unloaded. Then dismantle it and mask off any areas not intended for DuraCoat before spraying the product on the pieces.
Keep gun safety at the forefront of all activity involving a pistol, rifle or automatic weapon. After all, you could accidentally shoot yourself! The ask a well-trusted supplier about this new technology that allows people to customize their guns. Choose the colors and textures you like best and enjoy a new experience with a gun that reflects your personality.
About the Author:
Buy duracoat aerosol kit and many other accessories only on the Web. Check out this supplier's website now and select your favorite design at http://robinsonweaponry.com.
0 comments:
Post a Comment