If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You have to ensure that its bar clamp diameter would be suitable on its stem diameter. That has to be inspected as it will surely cause a lot of issues in the future. They would not be fit together when their diameters are different. Before an item is purchased, you must look at its diameter for you to prevent any waste of cash on the purchase you would be making.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You have to ensure that its bar clamp diameter would be suitable on its stem diameter. That has to be inspected as it will surely cause a lot of issues in the future. They would not be fit together when their diameters are different. Before an item is purchased, you must look at its diameter for you to prevent any waste of cash on the purchase you would be making.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
About the Author:
When you are looking for information about Profile Design Cobra Bars go to the web pages online here today. You can see details at http://www.sportfactoryproshop.com now.
0 comments:
Post a Comment